![]() If the ASB module is the end device on the RIO network then it must have a 150 Ohm terminating resistor placed between the two (2) signal conductors of the "Blue Hose" cable on the terminal arm of the ASB module. These settings configure the ASB adapter for 57.6kbps comm. Dip Switch 1=ON, Dip Switch 2=OFF, Dip Switches 4,5,6=OFF. 5- So what address do I put on rack number in SW2 (switch 4-8)? What address do I put on 1771-ASB SW1 (switch 1-6)? 6- What should I select on SW2 switch 2 (half or full) PLC 5/25ĭip Switch Block S2 on the ASB adapter. > Shoud I close SW3 switch 2= ON (End of DH+ node? 4- Remember I am using 1/2 slot addressing with 32 bits modules. 3- Should I close SW3 swtich 1 =ON (end of Remote I/O node? > SW2 switch 1 = OFF (for 57.6Kbs baud rate), > PLC5/25? 2- On my Processor (5/25) it is given that on > use Adapter mode or scanner mode for communicating b/w 1771-AB and > Adapter mode is selected and when scanner mode is selected, should I > 1- SW1 switch8= should be set on Adapter (ON) or scanner (OFF). Regarding DIP switches I have the following questions: ![]() ![]() > PC to PLC 5/25 by 1784-KTX card through DH+ link on programming port > indicates that u should check DIP switch setting). > Both LEDs Active and Fault are blinking at once on 1771-ASB module (it I am unable to communicate with PLC 5/-ASB module. > I have a PLC5/25 connected with 1771-ASB ser B module on Remote I/O What address do I put on 1771-ASB SW1 (switch 1-6)?Ħ- What should I select on SW2 switch 2 (half or full) PLC 5/25 processor? So my PLC chassis will occupy rack 0, rack 1, rack 2 and rack 3.ĥ- So what address do I put on rack number in SW2 (switch 4-8)? ![]() The Dual Slot Modules are fully programmable from the 1771 processor or from its on-board keypad, and offer position resolutions of up to 8,192 counts per turn for single turn applications, and up to 4096 counts/turn over 180 turns for multi-turn applications. Shoud I close SW3 switch 2= ON (End of DH+ node?Ĥ- Remember I am using 1/2 slot addressing with 32 bits modules. Both Dual and Single Slot modules are available for the 1771 I/O system. SW2 switch 1 = OFF (for 57.6Kbs baud rate),ģ- Should I close SW3 swtich 1 =ON (end of Remote I/O node? When Adapter mode is selected and when scanner mode is selected, should I use Adapter mode or scanner mode for communicating b/w 1771-AB and PLC5/25?Ģ- On my Processor (5/25) it is given that on Regarding DIP switches I have the following questions:ġ- SW1 switch8= should be set on Adapter (ON) or scanner (OFF). I have connected my PC to PLC 5/25 by 1784-KTX card through DH+ link on programming port (3 pin DH+ port). Both LEDs Active and Fault are blinking at once on 1771-ASB module (it indicates that u should check DIP switch setting). I have a PLC5/25 connected with 1771-ASB ser B module on Remote I/O port. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |